川崎製鉄技報 KAWASAKI STEEL GIHO Vol. 1(1969) No.3 |
||
低炭素鋼のCの析出におよぼすSeの影響 The Influence of Selenium on the Ageing of Low Carbon Steel 鶴岡 一夫(Kazuo Tsuruoka) 小野 寛(Yutaka Ono) 清水 洋(Yo Shimizu) 西田 稔(Minoru Nishida) 小林 邦彦(Kunihiko Kobayashi) p.223-237 PDF: 15P/727kb FeおよびFe−0.3%Cuの酸性硫酸塩水溶液中における分極挙動 The Polarization Behavior of Fe and Fe-0.3%Cu in Acidic Sulfate Solutions 後藤 実成(Minari Goto) 細田 博(Hiroshi Hosoda) p.238-247 PDF: 10P/338kb 面内曲げモーメントを受ける正方形板の後座屈挙動 Post Buckling Behavior of a Square Plate Subjected to Bending Stresses Applied in the Plane of Plate 浜田 敬之介(Keinosuke Hamada) p.248-257 PDF: 10P/324kb 水島製鉄所における連続鋳造設備の建設と操業について Construction and Operation of an 8 Strands Continuous Casting Machine for Bloom at Mizushima Works 川名 昌志(Masashi Kawana) 斎藤 達(Toru Saito) 三枝 誠(Makoto Saigusa) 五十嵐 清之(Kiyoyuki Igarashi) p.258-268 PDF: 11P/432kb R-H環流式真空脱ガス処理による調質鋼の品質向上,ならびに環流管用耐火物の開発 Development for Quality of Quenched and Tempered High Strength Steel by R-H Circulation Flow Degassing Process and Improvement of Refractories for Snorkels 太田 豊彦(Toyohiko Ota) 飯田 義治(Yoshiharu Iida) p.269-278 PDF: 10P/361kb H形鋼カリバー設計における一考察 A Consideration Concerning Roll Design for H-Shapes 小野 友太郎(Tomotaro Ono) 森川 欣則(Yoshinori Morikawa) 松室 知視(Tomomi Matsumuro) 辻 正幸(Masayuki Tsuji) 伊藤 守正(Morimasa Ito) p.279-289 PDF: 11P/367kb 直視式結晶方位解析装置の開発について A Special X-Ray Diffractometer for Determining the Crystal Orientation 鶴岡 一夫(Kazuo Tsuruoka) 安部 忠広(Tadahiro Abe) 深尾 良郎(Yoshiro Fukao) p.290-300 PDF: 11P/516kb 欧州における焼結鉱製造の新技術について New Technique Applied for Sintering Process in Europe 満岡 正彦(Masahiko Mitsuoka) p.309-320 PDF: 12P/459kb |
||
◆資料(直接PDFへ) ローリングミルによるリング製品について Ring Products Produced by Ring Rolling Mill 山浦 茂義(Shigeyoshi Yamaura) 松居 進(Susumu Matsui) 狩野 俊之(Toshiyuki Kano) 見戸 一成(Kazunari Mito) p.301-308 PDF: 8P/399kb |
||
※川崎製鉄技報本文はPDFファイルとなっています。 これをご覧いただくには、Adobe Acrobat Readerが必要です。 Adobe Acrobat Reader は、こちらから無料でダウンロードできます。 |トップページへ||技報トップページへ| (c)JFE Steel Corporation, 2003 |